7 Custom Tile Shower Mistakes to Avoid in Evansville, IN

A custom tile shower is one of the best upgrades you can make to a bathroom. It looks better than a prefab unit, it lasts far longer, and it is the feature buyers notice first. But a tile shower is only as good as the work behind the tile. A few common mistakes — some made by homeowners, some made by installers cutting corners — can turn a beautiful shower into a leak, a stain, or a tear-out a few years down the road.

Here are the seven mistakes to avoid when you remodel your shower in Evansville, and how to make sure your shower is built right the first time.

  1. Skipping Real Waterproofing

This is the big one. Tile and grout are not waterproof — water passes through them. What keeps a shower dry is the waterproof membrane underneath: behind the walls, under the floor, sealed at every corner and seam.

Some installers still use old methods like a plastic sheet behind cement board with gaps at the seams, or skip the membrane on the walls entirely. That is how water gets into the framing, and how a shower that looks fine on day one starts growing mold inside the wall by year three.

A proper tile shower has a continuous waterproofing system — membrane on the walls and floor, sealed corners, a sealed drain connection — before a single tile goes up. If an installer cannot explain their waterproofing system in plain English, that is a red flag.

2. A Flat Shower Floor That Does Not Drain

A shower floor has to slope toward the drain — about a quarter inch per foot. That sounds small, but it is the difference between a floor that dries in minutes and a floor with standing water in the corners.

Standing water does more than look bad. It breeds mildew, stains grout, and makes the floor slippery. And it is usually caused by a floor that was poured flat, or sloped the wrong way.

Before the tile goes down, the floor should be checked with a level. After the tile is set, water should run to the drain from every corner of the floor. This is one of the simplest things to get right — and one of the most expensive to fix later.

3. Choosing the Wrong Tile for the Floor

Wall tile and floor tile are not interchangeable. A glossy, large-format tile that looks great on a wall can be dangerously slippery under wet feet, and a tile that is too large can be hard to slope properly on a shower floor.

For shower floors, smaller tiles work better: two-inch mosaic tile, for example, gives you more grout lines for grip and follows the slope of the floor naturally. Porcelain is the safest bet for a shower — it absorbs almost no water and holds up to daily use. Natural stone can be beautiful, but it needs sealing and more maintenance, and some stones stain easily in a wet environment.

The right tile for the floor is one that is safe to stand on wet, easy to slope toward the drain, and tough enough for daily use. Looks matter — but in a shower, safety and drainage come first.

4. Forgetting the Niche — or Putting It in the Wrong Spot

A built-in niche is one of the most useful features in a custom tile shower. It holds shampoo, soap, and conditioner right where you reach for them, and it looks far better than a plastic caddy hanging from the shower head.

The mistake is treating the niche as an afterthought. If it is added after the walls are framed, it ends up in the wrong place — too high, too low, or on a wall with plumbing behind it where it cannot be cut in. A niche should be planned before framing, placed at a comfortable reaching height, and sized to fit the bottles you actually use.

It also needs to be waterproofed like the rest of the shower, with a slight slope on the bottom shelf so water drains out instead of pooling. A niche that holds a puddle is worse than no niche at all.

5. Using the Wrong Grout — or Skipping the Sealer

Grout is the part of a shower that takes the most abuse. It sits in standing water, collects soap scum, and is the first thing to stain or crack if it is the wrong product or applied poorly.

Standard sanded grout works for wider joints, but in a shower it needs to be sealed, and it needs to be resealed regularly. Epoxy grout costs more up front, but it resists stains and water far better, and it does not need sealing — which is why it is worth considering for a shower floor and the lower walls where water sits longest.

The other common mistake is rushing the grout. Grout that is applied before the thinset underneath has fully cured, or before the shower has had time to dry, will crack and crumble. A good installer lets each layer cure on schedule, even if it adds a day to the job. That patience is what keeps grout looking good years later.

6. Bad Ventilation That Ruins Good Tile Work

Even a perfectly built tile shower will struggle in a bathroom with no ventilation. Steam from a hot shower has to go somewhere. Without a working exhaust fan — or with a fan that is too small for the room — moisture settles on the walls, the ceiling, and the grout, and mildew follows.

Before you remodel the shower, check the fan. It should vent outside the house, not into the attic, and it should be sized for the room. A good rule is to run the fan during the shower and for about twenty minutes after. If your bathroom mirror fogs up and stays fogged, your fan is not doing its job.

Ventilation is not glamorous, but it protects every dollar you spend on tile. A shower that dries out between uses stays clean, and grout that dries out does not grow mildew.

7. Hiring on Price Alone

A custom tile shower from River City Flooring Pros runs $7,000 to $8,000 and takes about a week. That is the full job: demolition, waterproofing, tile, grout, fixtures, glass, and cleanup. When a quote comes in far below that, it is worth asking what is being left out.

The most common corners to cut are the ones you cannot see: thinner waterproofing, no membrane on the walls, cheap grout, a floor poured flat, or a rushed cure time. None of those show up in a photo of the finished shower. They show up a year or two later, when the fix costs more than the savings.

A fair price, a clear scope of work in writing, and an installer who can explain their waterproofing system are worth more than the lowest bid. Ask how the shower is waterproofed, what grout they use, and how long the job takes — and be wary of anyone who promises a full custom tile shower in two days.

The Bottom Line

Most tile shower problems are not bad luck. They are the result of a step that was skipped, rushed, or done with the wrong material — usually somewhere you cannot see. The good news is that every one of these mistakes is easy to avoid when the shower is planned and built properly.

A well-built custom tile shower should last decades: tile that stays put, grout that stays clean, a floor that drains, and walls that stay dry behind the tile. That is what you are paying for — not just the look on day one, but the shower still working perfectly on day one thousand.

Ready to Build Your Shower the Right Way?

If you are thinking about a custom tile shower in Evansville, start with a free estimate. River City Flooring Pros will measure your space, talk through tile choices, niches, benches, and glass, and give you a straight price — $7,000 to $8,000, about a week from start to finish — with the waterproofing done right the first time.

Call (812) 454-1631 for a free estimate. One week, one beautiful shower, and no mistakes to fix later.

Next
Next

How a Custom Tile Shower Adds Value to Your Evansville Home